Skip to main content
Physics LibreTexts

16.4: Procedures

  1. Last updated
  2. Save as PDF
  • Page ID
    29207

    • \( \newcommand{\vecs}[1]{\overset { \scriptstyle \rightharpoonup} {\mathbf{#1}} } \) \( \newcommand{\vecd}[1]{\overset{-\!-\!\rightharpoonup}{\vphantom{a}\smash {#1}}} \)\(\newcommand{\id}{\mathrm{id}}\) \( \newcommand{\Span}{\mathrm{span}}\) \( \newcommand{\kernel}{\mathrm{null}\,}\) \( \newcommand{\range}{\mathrm{range}\,}\) \( \newcommand{\RealPart}{\mathrm{Re}}\) \( \newcommand{\ImaginaryPart}{\mathrm{Im}}\) \( \newcommand{\Argument}{\mathrm{Arg}}\) \( \newcommand{\norm}[1]{\| #1 \|}\) \( \newcommand{\inner}[2]{\langle #1, #2 \rangle}\) \( \newcommand{\Span}{\mathrm{span}}\) \(\newcommand{\id}{\mathrm{id}}\) \( \newcommand{\Span}{\mathrm{span}}\) \( \newcommand{\kernel}{\mathrm{null}\,}\) \( \newcommand{\range}{\mathrm{range}\,}\) \( \newcommand{\RealPart}{\mathrm{Re}}\) \( \newcommand{\ImaginaryPart}{\mathrm{Im}}\) \( \newcommand{\Argument}{\mathrm{Arg}}\) \( \newcommand{\norm}[1]{\| #1 \|}\) \( \newcommand{\inner}[2]{\langle #1, #2 \rangle}\) \( \newcommand{\Span}{\mathrm{span}}\)\(\newcommand{\AA}{\unicode[.8,0]{x212B}}\)

    You will determine the height of the water line required for a raft to float.

    Do not place wood blocks into the water until specifically instructed.

    1. Draw a table in which to record physical quantities for your wood rafts.  Do not fill in data until you have read the instructions for obtaining that data.

    Table \(\PageIndex{1}\): Physical Quantities
     

    Mass (kg)

    Weight (N)

    Length (m)

    Width (m)

    Bottom Area (\(m^2\))

    Raft 1

    		          

    Raft 2

    		          

    Choose one of the wood blocks to be your 1st wood raft.  Use this raft for the following procedures.

    1. Measure and record the mass of your 1st raft, in kilograms.  Calculate and record the weight of your 1st wood raft in Newtons.  Repeat this process for your 2nd raft.

    2. Measure and record the length and width of your 1st raft, in meters.  Use these measurements to calculate the bottom area of your 1st raft, and record this value. Repeat this process for your 2nd raft.

    clipboard_eaa50f764c1b4fa73f2a5f668f52facbb.png
    Figure \(\PageIndex{1}\)

    1. Draw a 2nd table in which to record water line information.  Read the instructions for obtaining the data.

    Table \(\PageIndex{2}\): Water Line Height 
     

    Predicted

    Measured

    Error

    Raft 1

    		      

    Raft 2

    		      

    1. Hold the 1st wood raft in your hand and hypothesize (guess) the level to which the raft will need to sink into the water in order to float.  Predict where the water line will be, calculate or measure the predicted height from the bottom of the block to the level the water will rise, and record this height in centimeters, as the predicted water line height.  You may choose whether to simply predict this water line height or use the two equations for pressure to calculate it.  The density of water is 1,000 kg/m3.

    clipboard_e0acc944b4a389ed44d6c8b0c91ece763.png
    Figure \(\PageIndex{2}\)

    1. Fill the plastic tub about half full of water.  Gently place your 1st raft into the tub of water, carefully remove it, and measure the amount of the raft thickness that is wet, in centimeters.  Record this value as your measured water line height.

    clipboard_e05dfd9b05fab522a6a724c84a3d1694c.png
    Figure \(\PageIndex{3}\): Copy and Paste Caption here. (Copyright; author via source)

    1. Calculate and record the amount of error for this investigation, using your measured value as the standard value.

    2. Hold both wood rafts in your hands.  Discuss and hypothesize the level to which the 2nd wood raft will need to sink into the water in order to float.  Predict where the water line will be, calculate or measure the predicted height from the bottom of the block to the level the water will rise, and record this height in centimeters, as the predicted water line height.  You may choose whether to simply predict this water line height or use the two equations for pressure to calculate it.  The density of water is 1,000 kg/m3.

    3. Gently place your 2nd raft into the tub of water, carefully remove it, and measure the amount of the raft thickness that is wet, in centimeters.  Record this value as your measured water line height for your 2nd wood raft.  Calculate and record the amount of error, using your measured value as the standard value.

    Clean-up

    • Discard water outside (water plants)
    • Thoroughly dry everything used in the experiment

    Contributors and Attributions

    16.4: Procedures is shared under a CC BY license and was authored, remixed, and/or curated by LibreTexts.

    1. Back to top
    • Was this article helpful?

    Recommended articles

    1. Article type
      Section or Page
      License
      CC BY
    2. Tags
      This page has no tags.