# 12.3: Magnetic Force between Two Parallel Currents

- Page ID
- 4423

You might expect that two current-carrying wires generate significant forces between them, since ordinary currents produce magnetic fields and these fields exert significant forces on ordinary currents. But you might not expect that the force between wires is used to define the ampere. It might also surprise you to learn that this force has something to do with why large circuit breakers burn up when they attempt to interrupt large currents.

The force between two long, straight, and parallel conductors separated by a distance *r* can be found by applying what we have developed in the preceding sections. Figure shows the wires, their currents, the field created by one wire, and the consequent force the other wire experiences from the created field. Let us consider the field produced by wire 1 and the force it exerts on wire 2 (call the force \(F_2\)). The field due to \(I_1\) at a distance *r* is

\[B_1 = \frac{\mu_0I_1}{2\pi r}\]

**Figure \(\PageIndex{1}\):*** (a) The magnetic field produced by a long straight conductor is perpendicular to a parallel conductor, as indicated by right-hand rule (RHR)-2. (b) A view from above of the two wires shown in (a), with one magnetic field line shown for wire 1. RHR-1 shows that the force between the parallel conductors is attractive when the currents are in the same direction. A similar analysis shows that the force is repulsive between currents in opposite directions.*

This field is uniform from the wire 1 and perpendicular to it, so the force \(F_2\) it exerts on a length *l* of wire 2 is given by \(F = IlB \space sin \space \theta\) with \(sin \space \theta = 1\):

\[F_2 = I_2lB_1.\]

The forces on the wires are equal in magnitude, so we just write *F* for the magnitude of \(F_2\) (Note that \(\vec{F}_1 = -\vec{F}_2\).) Since the wires are very long, it is convenient to think in terms of *F/l*, the force per unit length. Substituting the expression for \(B_1\) into Equation and rearranging terms gives

Note

\[\frac{F}{l} = \frac{\mu_0I_1I_2}{2\pi r}.\]

The ratio *F/l* is the force per unit length between two parallel currents \(I_1\) and \(I_2\) separated by a distance *r*. The force is attractive if the currents are in the same direction and repulsive if they are in opposite directions.

This force is responsible for the ** pinch effect** in electric arcs and other plasmas. The force exists whether the currents are in wires or not. It is only apparent if the overall charge density is zero; otherwise, the Coulomb repulsion overwhelms the magnetic attraction. In an electric arc, where charges are moving parallel to one another, an attractive force squeezes currents into a smaller tube. In large circuit breakers, such as those used in neighborhood power distribution systems, the pinch effect can concentrate an arc between plates of a switch trying to break a large current, burn holes, and even ignite the equipment. Another example of the pinch effect is found in the solar plasma, where jets of ionized material, such as solar flares, are shaped by magnetic forces.

The definition of the **ampere** is based on the force between current-carrying wires. Note that for long, parallel wires separated by 1 meter with each carrying 1 ampere, the force per meter is

\[\frac{F}{l} = \frac{(4\pi \times 10^{-7}T \cdot m/A)(1 \space A)^2}{(2\pi)(1 \space m)} = 2 \times 10^{-7} \space N/m.\]

Since \(\mu_0\) is exactly \(4\pi \times 10^{-7} \space T \cdot m/A\) by definition, and because \(1 \space T = 1 \space N/(A \cdot m)\), the force per meter is exactly \(2 \times 10^{-7} \space N/m\). This is the basis of the definition of the ampere.

Infinite-length wires are impractical, so in practice, a current balance is constructed with coils of wire separated by a few centimeters. Force is measured to determine current. This also provides us with a method for measuring the coulomb. We measure the charge that flows for a current of one ampere in one second. That is, \(1 \space C = 1 \space A \cdot s\). For both the ampere and the coulomb, the method of measuring force between conductors is the most accurate in practice.

Example

Calculating Forces on Wires Two wires, both carrying current out of the page, have a current of magnitude 5.0 mA. The first wire is located at (0.0 cm, 3.0 cm) while the other wire is located at (4.0 cm, 0.0 cm) as shown in Figure. What is the magnetic force per unit length of the first wire on the second and the second wire on the first?

**Figure \(\PageIndex{2}\):*** Two current-carrying wires at given locations with currents out of the page.*

**Strategy**

Each wire produces a magnetic field felt by the other wire. The distance along the hypotenuse of the triangle between the wires is the radial distance used in the calculation to determine the force per unit length. Since both wires have currents flowing in the same direction, the direction of the force is toward each other.

**Solution**

The distance between the wires results from finding the hypotenuse of a triangle:

\[r = \sqrt{(3.0 \space cm)^2 + (4.0 \space cm)^2} = 5.0 \space cm.\]

The force per unit length can then be calculated using the known currents in the wires:

\[\frac{F}{l} = \frac{(4\pi \times 10^{-7}T \cdot m/A)(5 \times 10^{-3}A)^2}{(2\pi)(5 \times 10^{-2}m)} = 1 \times 10^{-10} \space N/m.\]

The force from the first wire pulls the second wire. The angle between the radius and the *x*-axis is

\[\theta = tan^{-1} \left(\frac{3 \space cm}{4 \space cm}\right) = 36.9^o.\]

The unit vector for this is calculated by

\[cos(36.9^o)\hat{i} - sin(36.9^o)\hat{j} = 0.8 \hat{i} - 0.6 \hat{j}.\]

Therefore, the force per unit length from wire one on wire 2 is

\[\frac{\vec{F}}{l} = (1 \times 10^{-10} \space N/m) \times (0.8\hat{i} - 0.6 \hat{j}) = (8 \times 10^{-11}\hat{i} - 6 \times 10^{-11}\hat{j}) \space N/m.\]

The force per unit length from wire 2 on wire 1 is the negative of the previous answer:

\[\frac{\vec{F}}{l} = (-8 \times 10^{-11}\hat{i} + 6 \times 10^{-11}\hat{j})N/m.\]

**Significance**

These wires produced magnetic fields of equal magnitude but opposite directions at each other’s locations. Whether the fields are identical or not, the forces that the wires exert on each other are always equal in magnitude and opposite in direction (Newton’s third law).

Note

**Check Your Understanding** Two wires, both carrying current out of the page, have a current of magnitude 2.0 mA and 3.0 mA, respectively. The first wire is located at (0.0 cm, 5.0 cm) while the other wire is located at (12.0 cm, 0.0 cm). What is the magnitude of the magnetic force per unit length of the first wire on the second and the second wire on the first?

[Hide Solution]

Both have a force per unit length of \(9.23 \times 10^{-12} \space N/m\)

## Contributors

Paul Peter Urone (Professor Emeritus at California State University, Sacramento) and Roger Hinrichs (State University of New York, College at Oswego) with Contributing Authors: Kim Dirks (University of Auckland) and Manjula Sharma (University of Sydney). This work is licensed by OpenStax University Physics under a Creative Commons Attribution License (by 4.0).