Loading [MathJax]/jax/output/HTML-CSS/jax.js
Skip to main content
Library homepage
 

Text Color

Text Size

 

Margin Size

 

Font Type

Enable Dyslexic Font
Physics LibreTexts

7.5: Why 50 Ohms?

( \newcommand{\kernel}{\mathrm{null}\,}\)

The quantity 50 Ω appears in a broad range of applications across the field of electrical engineering. In particular, it is a very popular value for the characteristic impedance of transmission line, and is commonly specified as the port impedance for signal sources, amplifiers, filters, antennas, and other RF components. So, what’s special about 50 Ω? The short answer is “nothing.” In fact, other standard impedances are in common use – prominent among these is 75 Ω. It is shown in this section that a broad range of impedances – on the order of 10s of ohms – emerge as useful values based on technical considerations such as minimizing attenuation, maximizing power handling, and compatibility with common types of antennas. Characteristic impedances up to 300 Ω and beyond are useful in particular applications. However, it is not practical or efficient to manufacture and sell products for every possible impedance in this range. Instead, engineers have settled on 50 Ω as a round number that lies near the middle of this range, and have chosen a few other values to accommodate the smaller number of applications where there may be specific compelling considerations.

So, the question becomes “what makes characteristic impedances in the range of 10s of ohms particularly useful?” One consideration is attenuation in coaxial cable. Coaxial cable is by far the most popular type of transmission line for connecting devices on separate printed circuit boards or in separate enclosures. The attenuation of coaxial cable is addressed in Section 7.3. In that section, it is shown that attenuation is minimized for characteristic impedances in the range (60 Ω)/ϵr to (77 Ω)/ϵr, where ϵr is the relative permittivity of the spacer material. So, we find that Z0 in the range 60 Ω to 77 Ω is optimum for air-filled cable, but more like 40 Ω to 50 Ω for cables using a plastic spacer material having typical ϵr2.25. Thus, 50 Ω is clearly a reasonable choice if a single standard value is to be established for all such cable.

Coaxial cables are often required to carry high power signals. In such applications, power handling capability is also important, and is addressed in Section 7.4. In that section, we find the power handling capability of coaxial cable is optimized when the ratio of radii of the outer to inner conductors b/a is about 1.65. For the air-filled cables typically used in high-power applications, this corresponds to a characteristic impedance of about 30 Ω. This is significantly less than the 60 Ω to 77 Ω that minimizes attenuation in air-filled cables. So, 50 Ω can be viewed as a compromise between minimizing attenuation and maximizing power handling in air-filled coaxial cables.

Although the preceding arguments justify 50 Ω as a standard value, one can also see how one might make a case for 75 Ω as a secondary standard value, especially for applications where attenuation is the primary consideration.

Values of 50 Ω and 75 Ω also offer some convenience when connecting RF devices to antennas. For example, 75 Ω is very close to the impedance of the commonly-encountered half-wave dipole antenna (about 73+j42 Ω), which may make impedance matching to that antenna easier. Another commonly-encountered antenna is the quarter-wave monopole, which exhibits an impedance of about 36+j21 Ω, which is close to 50 Ω. In fact, we see that if we desire a single characteristic impedance that is equally convenient for applications involving either type of antenna, then 50 Ω is a reasonable choice.

A third commonly-encountered antenna is the folded half-wave dipole. This type of antenna is similar to a half-wave dipole but has better bandwidth, and is commonly used in FM and TV systems and land mobile radio (LMR) base stations. A folded half-wave dipole has an impedance of about 300 Ω and is balanced (not single-ended); thus, there is a market for balanced transmission line having Z0=300 Ω. However, it is very easy and inexpensive to implement a balun (a device which converts the dipole output from balanced to unbalanced) while simultaneously stepping down impedance by a factor of 4; i.e., to 75 Ω. Thus, we have an additional application for 75 Ω coaxial line.

Finally, note that it is quite simple to implement microstrip transmission line having characteristic impedance in the range 30 Ω to 75 Ω. For example, 50 Ω on commonly-used 1.575 mm FR4 requires a width-to-height ratio of about 2, so the trace is about 3 mm wide. This is a very manageable size and easily implemented in printed circuit board designs.

Additional Reading:

  • “Dipole antenna” on Wikipedia.
  • “Monopole antenna” on Wikipedia.
  • “Balun” on Wikipedia.

This page titled 7.5: Why 50 Ohms? is shared under a CC BY-SA license and was authored, remixed, and/or curated by Steven W. Ellingson (Virginia Tech Libraries' Open Education Initiative) .

Support Center

How can we help?