# 4.3: Intensity in Single-Slit Diffraction

- Page ID
- 4507

LEARNING OBJECTIVES

By the end of this section, you will be able to:

- Calculate the intensity relative to the central maximum of the single-slit diffraction peaks
- Calculate the intensity relative to the central maximum of an arbitrary point on the screen

To calculate the intensity of the diffraction pattern, we follow
the phasor method used for calculations with ac circuits in
Alternating-Current Circuits. If we consider that there are
\(N\) Huygens sources across the slit shown
previously, with each source separated by a distance a/N from
its adjacent neighbors, the path difference between waves from
adjacent sources reaching the arbitrary point *P* on the
screen is \((a/N) \, \sin \theta\). This distance is equivalent to
a phase difference of \((2\pi a/\lambda N) \, \sin \, \theta\). The
phasor diagram for the waves arriving at the point whose angular
position is \(\theta\) is shown in Figure \(\PageIndex{1}\). The
amplitude of the phasor for each Huygens wavelet is \(\Delta E_0\),
the amplitude of the resultant phasor is \(E\), and the phase
difference between the wavelets from the first and the last sources
is

\[\phi = \left(\dfrac{2\pi}{\lambda}\right) \, a \, \sin \theta. \]

With \(N → ∞\), the phasor diagram approaches a circular arc of
length \(N \Delta E_0\) and radius \(r\). Since the length of the
arc is \(N \Delta E_0\) for any \(ϕ\), the radius *r* of the
arc must decrease as \(ϕ\) increases (or equivalently, as the
phasors form tighter spirals).

The phasor diagram for ϕ = 0 (the center of the diffraction
pattern) is shown in Figure \(\PageIndex{1a}\) using N=30. In this
case, the phasors are laid end to end in a straight line of length
\(N \Delta E_0\), the radius *r* goes to infinity, and the
resultant has its maximum value \(E = N\Delta E_0\). The intensity
of the light can be obtained using the relation \(I = \dfrac{1}{2}
c \epsilon_0 E^2\) from
Electromagnetic Waves. The intensity of the maximum is then

\[I_0 = \dfrac{1}{2} c\epsilon_0 (N \Delta E_0)^2 = \dfrac{1}{2\mu_0 c}(N\Delta E_0)^2, \]

where \(\epsilon_0 = 1/\mu_0 c^2\). The phasor diagrams for the first two zeros of the diffraction pattern are shown in Figure \(\PageIndex{1b}\) and Figure \(\PageIndex{1d}\). In both cases, the phasors add to zero, after rotating through \(\phi = 2\pi\) rad for m = 1 and \(4 \pi\) rad for m = 2.

The next two maxima beyond the central maxima are represented by the phasor diagrams of parts (c) and (e). In part (c), the phasors have rotated through \(\phi = 3\pi\) rad and have formed a resultant phasor of magnitude \(E_1\). The length of the arc formed by the phasors is \(N\Delta E_0\). Since this corresponds to 1.5 rotations around a circle of diameter \(E_1\), we have

\[\dfrac{3}{2} \pi E_1 = N \Delta E_0, \]

so

\[E_1 = \dfrac{2N\Delta E_0}{3\pi} \]

and

\[I_1 = \dfrac{1}{2\mu_0 c}E_1^2 = \dfrac{4(N\Delta E_0)^2}{(9\pi^2)(2\mu_0c)} = 0.045 I_0,\]

where

\[I_0 = \dfrac{(N\Delta E_0)^2}{2\mu_0 c}.\]

In part (e), the phasors have rotated through \(\phi = 5\pi\) rad, corresponding to 2.5 rotations around a circle of diameter \(E_2\) and arc length \(N\Delta E_0\). This results in \(I_2 = 0.016 I_0\). The proof is left as an exercise for the student (Exercise 4.119).

These two maxima actually correspond to values of ϕ slightly less than \(3\pi\) rad and \(5\pi\) rad. Since the total length of the arc of the phasor diagram is always \(N \Delta E_0\), the radius of the arc decreases as \(ϕ\) increases. As a result, \(E_1\) and \(E_2\) turn out to be slightly larger for arcs that have not quite curled through \(3\pi\) rad and \(5\pi\) rad, respectively. The exact values of \(ϕ\) for the maxima are investigated in Exercise 4.120. In solving that problem, you will find that they are less than, but very close to, \(\phi = 3\pi, \, 5\pi, \, 7\pi,\)… rad.

To calculate the intensity at an arbitrary point *P* on
the screen, we return to the phasor diagram of Figure
\(\PageIndex{1}\). Since the arc subtends an angle ϕ at the center
of the circle,

\[N\Delta E_0 = r\phi \label{eq10}\]

and

\[sin \left(\dfrac{\phi}{2}\right) = \dfrac{E}{2r}. \label{eq11}\]

where \(E\) is the amplitude of the resultant field. Solving the Equation \ref{eq11} for \(E\) and then substituting \(r\) from Equation \ref{eq10}, we find

\[\begin{align*} E &= 2r \, \sin \, \dfrac{\phi}{2} \\[5pt] &= 2\dfrac{N\Delta E_0}{\phi} \sin \, \dfrac{\phi}{2}. \end{align*}\]

Now defining

\[\beta = \dfrac{\phi}{2} = \dfrac{\pi a \, sin \, \theta}{\lambda} \label{4.2}\]

we obtain

\[E = N\Delta E_0 \dfrac{sin \, \beta}{\beta} \label{eq15}\]

Equation \ref{eq15} relates the amplitude of the resultant field at any point in the diffraction pattern to the amplitude \(N \Delta E_0\) at the central maximum. The intensity is proportional to the square of the amplitude, so

\[I = I_0 \left(\dfrac{sin \, \beta}{\beta}\right)^2 \label{eq20}\]

where \(I_0 = (N\delta E_0)^2/2\mu_0 c\) is the intensity at the center of the pattern.

For the central maximum, ϕ = 0, β is also zero and we see from l’Hôpital’s rule that \(lim_{\beta \rightarrow 0}(sin \, \beta/\beta) = 1\), so that \(lim_{\phi \rightarrow 0}I = I_0\). For the next maximum, \(\phi = 3\pi\) rad, we have \(\beta = 3\pi/2\) rad and when substituted into Equation \ref{eq20}, it yields

\[I_1 = I_0 \left(\dfrac{sin \, 3\pi/2}{3\pi/2}\right)^2 = 0.045 I_0,\]

in agreement with what we found earlier in this section using the diameters and circumferences of phasor diagrams. Substituting \(\phi = 5\pi\) rad into Equation \ref{eq20} yields a similar result for \(I_2\).

A plot of Equation \ref{eq20} is shown in Figure \(\PageIndex{3}\) and directly below it is a photograph of an actual diffraction pattern. Notice that the central peak is much brighter than the others, and that the zeros of the pattern are located at those points where \(sin \, \beta = 0\), which occurs when \(\beta = m\pi\) rad. This corresponds to

\[\dfrac{\pi a \, sin \theta}{\lambda} = m\pi,\]

or

\[a \, sin \, \theta = m \lambda,\]

which we derived for the destructive interference ro a single slit previously.

Example \(\PageIndex{1}\): Intensity in Single-Slit Diffraction

Light of wavelength 550 nm passes through a slit of width 2.00 μm and produces a diffraction pattern similar to that shown in Figure \(\PageIndex{3a}\) Find the locations of the first two minima in terms of the angle from the central maximum and (b) determine the intensity relative to the central maximum at a point halfway between these two minima.

**Strategy**

The minima are given by Equation 4.2.1, \(a \, sin \, \theta = m\lambda\). The first two minima are for m = 1 and m = 2. Equation \ref{eq20} and Equation \ref{4.2} can be used to determine the intensity once the angle has been worked out.

**Solution**

- Solving Equation
4.2.1 for θ gives us \(\theta_m = sin^{-1}(m\lambda/a)\), so
that
\[\theta_1 = sin^{-1} \left(\dfrac{(+1)(550 \times 10^{-9} m)}{2.00 \times 10^{-6}m}\right) = +16.0°\]

and\[\theta_2 = sin^{-1} \left(\dfrac{(+2)(550 \times 10^{-9}m)}{2.00 \times 10^{-6}m}\right) = +33.4°.\]

- The halfway point between \(\theta_1\) and \(\theta_2\) is
\[\theta = (\theta_1 + \theta_2) /2 = (16.0° + 33.4°)/2 = 24.7°.\]

Equation \ref{4.2} gives

\[\beta = \dfrac{\pi a \, sin \, \theta}{\lambda} = \dfrac{\pi (2.00 \times 10^{-6}m) \, sin \, (24.7°)}{(550 \times 10^{-9}m)} = 1.52\pi \, or \, 4.77 \, rad.\]

From Equation \ref{eq20}, we can calculate

\[\dfrac{I}{I_0} = \left(\dfrac{sin \, \beta}{\beta}\right)^2 = \left(\dfrac{sin \, (4.77)}{4.77}\right)^2 = \left(\dfrac{-0.9985}{4.77}\right)^2 = 0.044.\]

SignificanceThis position, halfway between two minima, is very close to the location of the maximum, expected near \(\beta = 3\pi/2\), or \(1.5\pi\).

Exercise \(\PageIndex{1}\)

For the experiment in Example \(\PageIndex{1}\), at what angle from the center is the third maximum and what is its intensity relative to the central maximum?

**Answer**-
\(74.3^o\), \(0.0083 I_0\)

If the slit width \(a\) is varied, the intensity distribution
changes, as illustrated in Figure \(\PageIndex{4}\). The central
peak is distributed over the region from \(sin \, \theta =
-\lambda/a\) to \(sin \, \theta = +\lambda/a\). For small θ, this
corresponds to an angular width \(\Delta \theta \approx 2\lambda
/a\). Hence, an increase in the slit width results in a decrease in
the **width of the central peak**. For a slit with a ≫
λ, the central peak is very sharp, whereas if a ≈ λ, it becomes
quite broad.

Diffraction Simulation

A diffraction experiment in optics can require a lot of preparation but this simulation by Andrew Duffy offers not only a quick set up but also the ability to change the slit width instantly. Run the simulation and select “Single slit.” You can adjust the slit width and see the effect on the diffraction pattern on a screen and as a graph.

## Contributors and Attributions

Samuel J. Ling (Truman State University), Jeff Sanny (Loyola Marymount University), and Bill Moebs with many contributing authors. This work is licensed by OpenStax University Physics under a Creative Commons Attribution License (by 4.0).